Sunday, March 22, 2009

Explore Sungai Siput New Offroad
























even i'm smoking, but the main point is i'm relax and recharge my enegy. : }









This trip, our tyre been punture 3 times. : {





did you see the lion hill















oooo.... sleepy man





my bike.. hehe






















the band of brother II









nice view









Hi Everybody, i'm Jack : ]






Yeah, i did it, i did it




Perak River

Saturday, March 21, 2009

Emergency bike repair

Emergency bike repairs
By BikeRadar


Seatpost Emergency Repair (BikeRadar)







What do you do when your bike breaks down miles from home? You can stick out your thumb, you can call a cab, or with a bit of preparation and ingenuity, you can get yourself home. Here's how.




Preparation is the key. As well as the basics of a pump, multi-tool and a spare inner-tube or two, carry a survival kit of essential spares and materials. Use a small container, such as an old Tip-Top patch kit box or a 35mm film canister, and fill it with the following, packing them in tightly so as not to rattle:




Small and medium zip-ties




A small piece of cut-down Biro casing wrapped with a length of duct tape
One or two SRAM Power Links, 9 and/or 10-speed, depending on your bike and those of people you ride with if you want to be Bicycle Repair Man.


These links will work with most chains
A small length of malleable wire (copper wire that can be twisted by hand is best)
Some 20p or 50p coins



A piece of tyre casing or other suitable material cut down to about 5cm square
Optionally, a spare 5mm Allen bolt or two, about 2.5cm in length, and 4mm and 6mm Allen bolts if you have enough space to fit them in your container
A St Christopher medallion or lucky charm!


Bike prep for panic prevention
Replace a couple of your shorter 5mm bottle-cage bolts with longer ones that are 3-4cm; these can be used on many modern twin bolt seatposts or clamps.


Fill your tubes with tyre sealant such as Slime. This can be extremely effective at warding off the debris from recently trimmed hedgerow. You can buy pre-filled tubes or inject sealant into Schrader or two-piece Presta valves. To treat tubes with one-piece Presta valves, you can cut a hole in them (as small a possible!), inject the sealant and fix it afterwards.


Buy a couple of spare normal spokes of the right length, with nipples, and tape them or zip tie them tightly under the left chainstay to keep them out of sight – they are handy to have in reserve. Now you're all set, here's how to use your emergency kit to deal with common problems








Loose jockey wheels


Jockey wheels have an annoying habit of coming loose, usually because they weren't tightened correctly after cleaning. That piece of copper wire or the 5mm bolt you've got can now do its thing. Just loop the cable through the centre of the jockey wheel to keep it in place.









Badly slashed tyre



Use your handy survival kit duct tape and install a slightly larger piece overlapping the bead of the tyre, thus anchoring it securely when inflated. You might want to put a second layer, or even use the piece of cloth or tyre casing, which you also happen to have in your box of tricks.
Broken seatpost clamp







No spare tube



Carefully tear the tube apart at the puncture, then tightly knot both ends; or do the same with your handy zip-ties. The tube will expand back into the tyre upon infl ation, but go easy on the pressure.








Bent rear mech or gear hanger


Place the bent rear mech into the smallest cog and big ring, then carefully and slowly pull the derailleur back into position. The cage of the rear mech should be in line with the smallest sprocket and check that it's pointing in a perpendicular direction to the ground.
Be careful when selecting the lowest gear while riding afterwards though, as the derailleur might no longer be as well adjusted and could get caught in the spokes.








Broken Rear Mech Or Gear Hanger


If your derailleur or hanger is broken beyond repair, you can remove it entirely and then shorten your chain using the SRAM Power Links in your survival kit. This repair depends on a bit of luck and preparation –


having a multi-tool that includes a chain breaker will make life a lot easier, though you might not be able to get ideal chain tension if you have vertical dropouts. Try to get the chain line as straight as possible.







Bolt-on repairs


You can pinch a bolt from a place on the bike where it can be spared, and use it where it's more critical in an emergency. If you lose a stem bolt, for example, you can borrow one from a rack strut or from a water bottle cage bolt. But be careful and go easy until a permanent replacement can be found, especially if you think carbon parts might be damaged. Run a cloth lightly over suspect areas to check for a cracked surface – any small cracks will pull the cloth's threads.






Pretzeled wheel


If replacing a spoke won't do or isn't an option, a pretzeled wheel can be straightened sufficiently to get you home with a bit of technique and brute force. Place the wheel with the axle and high point of the buckle against the ground, then firmly push with substantial weight while gripping the rim on either side of the bent zone. You can focus and increase your leverage by using your feet in place of hands and body weight, along with a stone or raised surface feature such as a kerb.


Having your brake quick release open will reduce the chances of the wheel rubbing all the way home. Exceptions might be if you have a delicate carbon frame with tight clearances, where a few miles of tyre rub could not only result in a blowout, but put a hole in your chainstays, seatstays, or fork blades. Those spare coins might come in handy now if you forgot your phone or ran out of battery charge.







Tyre removal


A useful trick is knowing how to remove a tyre without the aid of tyre levers. First, make sure all the air is removed, then lean over the wheel, holding it vertically against the ground. Starting with both hands at the top, pinch and manipulate the tyre beads into the centre of the rim channel simultaneously, with both hands working downwards.


As your hands meet towards the bottom you'll find that you've gained a substantial amount of slack, which should be enough to just pull the bead over the rim flange. If it's still a little tight, remove your quick-release skewer and use the lever – it works!


Check the tyre for any debris before fitting the new inner tube. Run your hands all the way round the inside of the wheel rim to feel for anything that may have pierced the casing such as a thorn or piece of glass, taking care not to cut your fingers.







Gear cable repairs


If you break a gear cable, it's most likely to be the rear one, in the lever itself or near the head-tube where most friction occurs.


Remove your front derailleur cable and carefully thread it through the right lever (you'll probably have to twist it in the direction of the winding to stop the strands from fraying). Tie it using a square knot onto the cable attached to the rear mech, about halfway along the down-tube.


Before tying the knot, push the mech up onto the big cog. This will take up any slack when it's released – though with a multi-tool you can take up the slack in the usual way.
You can also immobilise the derailleur in a specific gear if all cable options are gone – jam a twig or piece of debris in the parallelogram, after placing it into the desired gear.


Yeti 575 09" review














It’s light, it has almost six inches of travel and it’s controlled, smooth and accurate. The Yeti 575 might just be the ultimate trail bike.

There are heavy 5in travel bikes on the market, and there are light 6in travel bikes. And there’s the Yeti 575. The name refers to its 5.75in of suspension travel. On the face of it, the Yeti offers the best of both worlds.

The 575 comes close to being ideal for my preferred type of riding. It rewards smooth style, but allows you to throw caution to the wind when you’re trying to stick with guys on more hardcore all-mountain rigs on the downs. Then you just pull away from those riders struggling with their 34-pounders on the ups. That’s my sort of bike.


Ride & handling: smooth, plush medium-hit eater

You’ll instantly notice how buttery-plush the 575’s ride feel is. Obviously this depends on how you fettle the shock, but the attributes of the frame would be wasted if you set it up harsh. Set up soft, the back end makes small rocks and roots irrelevant, and medium-sized hits barely hinder your progress.

If you’re comparing the 575 with Yeti’s shorter-travel AS-R, it’s on those medium-sized hits where you can really let loose on a 575. The AS-R demands more finesse, but the 575 allows you to get messy from time to time. It forgives occasional bad line choice and permits the sort of carefree antics you expect from a 6in travel bike, but don’t always expect from a sub-28lb bike.

While everything remains plush over most terrain, a ramp-up towards the end of the compression means it takes a really big hit to reach maximum travel. You always feel as though the bike is holding a little reserve for blunders and risks. That’s a good feeling.

The ride is stable and efficient under steady pedal power, but if you’re an out-of-the-saddle uphill power masher you’ll need to use Fox’s ProPedal settings and lockout lever on the rear shock. Elsewhere, you’ll just want to make full use of the deep-pile-carpet ride.

It’s a joy on fast and challenging singletrack, and we couldn’t find a descent that fazed the back end, even when we were getting almost full travel on the fork.
Frame: Tuned for fun & feel

The detail of the 575 shows off almost every single recent advancement in frame design and building. The swoopy hydroformed top tube is octagonal in cross-section, beefed-up behind the reinforced head tube and generally shaped to boost stiffness along its complete length, but in particular where the shock and the dogbone link tube are attached.

The new rear triangle is carbon composite.

The top tube’s radically downward swoop – to improve standover height – the generous mud room and quality pivot bearings throughout stress Yeti’s thoroughly practical approach.
Every single frame segment is sculpted to achieve the ideal mix of high strength, lateral rigidity and low weight.

The dog bone bridging the seat stays and lower shock mount across to the top tube is a crucial part of the design. It guides and braces the carbon swingarm, controls the shock’s compression curve and lessens side loads on the shock.

This all combines nicely with the slight vertical flex built into the swingarm by the drop-outs in helping to dictate a super-plush ride.

The frame’s main pivot sits just above the bottom bracket, between the inner and middle chainrings.

Neat aluminium sections holding the bearings are bonded into the asymmetric carbon swingarm.
A tough wrap-around sheath with an extra deflector plate by the chainrings stops chain slap from damaging the right chain stay.

There’s a single set of bottle bosses, and a through-guide option of running full outer cable to the rear gear.

The medium sized frame weighs about 6lb, including the Fox Float RP23 shock. While unwanted shock bob isn’t really an issue here, there are three ProPedal damping settings and a lockout option.

As well as the anodised pewter of our test bike, it comes in anodised black, team turquoise or orange.
Verdict: perfect hard & fast trail bike

We can understand why Yeti bikes command passionate loyalty from those who own them. Every model in the range has an aura of pure performance, not to mention the classy and thoroughly practical design and build quality.

The 575 frame is lighter than most that offer this much travel, and it’s by no means the sort of bike you’d go throwing off big drops. But, built with sensible XT level componentry and beefy tyres, it’s a great choice for the sort of hard and fast trail riding that most of us can manage within the limits of our nerve. -->
Quote " Steve Worland, bike radar, Yeti 575 (09) review, http://www.bikeradar.com/gear/category/bikes/mountain/product/575-09-32275

Tuesday, March 17, 2009

MTB technique sharing

Bunny hops. may this video will improve your mtb riding technique






Front Wheel Hops

Wheelies



forward foot technique

Endo Side Drop

Sunday, March 15, 2009

unveil new offroad ( Sg siput)


Today 4pm with raining, we plan to explore more offroad for Sungai Siput MTB team, thus we have start to explore one very interesting offroad with great view, passing palm estate, rubber farm, pig farm. unfortunately we don't have enought time to continue the route. but very soon, we will reveil this mystery route. however i have upload the route detail and evelation for your reference. Dude, i hope soon or later we can ride this route again..